If you’re looking for the perfect centerpiece for your garden this spring, this disco birdbath is for you! Revamp that broken birdbath that’s been collecting dust in your garage with this easy facelift! Don’t have a birdbath? Build your own out of terracotta pots! We’re loving this easy tutorial from Patricia’s Pots, which takes you through the whole process, step-by-step. Give your feathered friends their own place to party (and recycle in the process!) by getting started on this awesome birdbath today!

What you will need:

– An old birdbath or a birdbath made from terracotta pots

– Water Weld (just in case your old birdbath has any cracks)

– Old DVDs

– Clear spray paint

– Liquid Nails Clear Seal glue

– Mapei Keracolor Sanded Grout with Polymer with Grout Boost mixed in

– An old spatula

– Damp rag

– An old butter knife

– Sandpaper

– Scissors

Step #1:

If your old birdbath has any cracks in it, you need to fill them in. Water Weld is perfect for the job since it repairs and seals cracks that are going to be wet or underwater. It’s also drinking water safe, which makes it perfect for the birds! Take the Water Weld (it comes in a tube of clay) and kneed it together well. Take your old butter knife and slice the Water Weld into smaller pieces.

Step #2:

Smooth the Water Weld over the cracks using the butter knife, making sure to push it into the cracks well. Leave the Water Weld to sit for 60 minutes.

Step #3:

Take the sandpaper and sand down the Water Weld until the surface is smooth.

Step #4:

Now you’re ready to decorate! Since DVDs are made up of two layers, you’ll need to separate them in order to get to the nice shiny side that’s inside. Take the DVD and make two cuts. Cut from the outer edge to the middle, and repeat the same process on the other side. You should now have two halves. Run your fingertip around the edges to loosen the layers. Separate the layers and you will be left with a thin, shimmery layer you can use for decorating your birdbath.

Step #5:

Cut the silvery part you saved into small pieces. This birdbath needed about 20 DVDs worth of pieces to cover it completely.

Step #6:

Take your clear spray paint and spray paint all the pieces. This will prevent the shiny part from flaking off.

Step #7:

Once the spray paint has dried, begin gluing the pieces onto the birdbath using Liquid Nails Clear Seal. Cover the rim of the birdbath first, then work your way towards the middle.

Step #8:

When you’ve covered your birdbath and the glue has dried, it’s time to mix the grout. You can use Mapei Keracolor Sanded Grout with Polymer in white with Grout Boost mixed in. When you’ve mixed the grout, take your old spatula and spread the grout between the DVD pieces. Use a damp rag to wipe off the excess grout.

Step #9:

Leave the grout to dry for about 3 weeks before placing it outside. This is why this is the perfect project to get started on while it’s still chilly out! It’ll be ready for your feathered friends just in time for spring!

Photos and idea: Me and My DIY.

Cleaning your bathroom is definitely not a fun, nor easy task to do. Who likes scrubbing the toilet and cleaning out hairs from the drainage? Every time we look to get the job done as fast as possible, but end up doing more bad than good. We’ve rounded up some of the most common mistakes you are probably already guilty of doing right now.

1. Using One Product for Everything

Don’t think a spray of Windex is all you need to clean your bathroom – every area needs it only specific product fit for the job. Glass cleaner may make thinks look shiny and pretty, but deep down it’s really not doing much. Use a tub-and-tile spray like Mr. Clean to deep clean germs and dirt, and save the Windex for your mirrors and windows.

 2. Putting Back a Wet Toilet Brush

After cleaning your toilet with the toilet brush, putting a soaking brush back into the holder is just asking for trouble. A breeding ground of germs and bacteria forms and is definitely not something you want to have in your home. Instead, place the brush across the toilet seat and allow all the water to drip down into the bowl and dry completely before putting it back.

3. Only Cleaning Obviously Dirty Parts

Even if some parts of your bathroom already look clean, there is no reason you shouldn’t freshen them up. Germs and bacteria can’t be seen so it’s important to get at every corner like your bathroom wall tiles, and not to mention that dirty grout! If dirty, discolored grout is a big culprit in your bathroom, consider installing PVC bathroom cladding. These bathroom panels are cheap to install, and will save you a lot of pain cleaning in the long run.

4. Not Turning on the Fan

Keeping the fan running is one of the best ways to cut out the formation of mold and bacteria from growing in your bathroom. Before getting into the shower, turn it on and then leave it running for about 20 minutes after your are done. This way it will suck out the moisture and keep your bathroom nice and dry. You can also just open up the window and create a draft to dry up your space.

5. Keeping the Shower Curtain Open

An open bunched up shower curtain is a culprit for attracting mildew and mold. After showering make sure to pull the curtain closed so it can dry easier. If you noticed a cloudy build up on your curtain, toss it in the washing machine on a gentle cycle with some towels and a little bit of bleach.

6. Skimping on Cleaning Little Details

The tiniest details in your bathroom can be the dirtiest like doorknobs, drawer pulls, and not to mention the toilet handle! Make sure to thoroughly disinfect and wipe down everything to make sure you aren’t spreading even more germs around your bath.

If you’ve had enough of dirty grout, we’ve got the solution! Choose from one of these 5 grout-cleaning recipes that are sure to get your grout looking good as new! Using only basic household ingredients, these recipes are great for people looking for a cheap and easy solution to cleaning their grout.

Recipe #1:

This recipe is mild, and can be used on all tile surfaces. You can also use it to remove stains from natural stone.

– 3 cups baking soda

– 1 cup water

Mix the baking soda until it forms a paste and apply it to the grout. Leave it to work for 10 minutes and rinse it clean.

Recipe #2:

Since this recipe uses vinegar, don’t use it on marble, limestone, or travertine.

– 1/4 cup salt

– 1/4 cup baking soda

– 1/4 cup vinegar

Mix the ingredients and apply it to the grout. Leave it for 20 minutes and make sure it doesn’t dry out. After the 20 minutes are up, give the grout a good scrub and rinse.

Recipe #3:

Use this recipe on light colored or white grout.

– 1/4 cup bleach

– 3/4 cup baking soda

Mix and apply to dirty grout. If you want to dilute the bleach, you can add water. The longer you leave the solution on, the brighter your grout will be.

Recipe #4:

This recipe works with all tile, except limestone or travertine.

– lemon juice

– baking soda

Mix into a paste and apply to dirty grout. Leave it for 20 minutes, then scrub and rinse.

Recipe #5:

Don’t use this bleach on colored grout, and test it first on marble surfaces.

– 3 parts baking soda

– 1 part hydrogen peroxide

Mix into a paste and apply it to your grout. Leave it to sit for 20 minutes and scrub well. Rinse with warm water. This mixture can also be used on poultice and natural stone.

Photos: Flooring Hunt, Deco Bizz, Skroutz On Deck.